Linux Basement Presents: Chad’s Blog

Asterisk on Hardy Server

My notes on installing the latest Asterisk from Source on Ubuntu Hardy.

Fresh hardy install with only SSH and base packages.

apt-get install linux-headers-$(uname -r) build-essential automake autoconf bison flex libtool libncurses5-dev libssl-dev subversion

wget http://downloads.digium.com/pub/asterisk/releases/asterisk-1.4.21.2.tar.gz

wget http://downloads.digium.com/pub/zaptel/releases/zaptel-1.4.11.tar.gz

wget http://downloads.digium.com/pub/libpri/releases/libpri-1.4.7.tar.gz

tar xfvz zaptel-1.4.11.tar.gz -C /usr/src/

tar xfvz asterisk-1.4.21.2.tar.gz -C /usr/src/

tar xfvz libpri-1.4.7.tar.gz -C /usr/src/

cd /usr/src/zaptel-1.4.11

./configure

make

make install

Zaptel installed no problem.

cd ../libpri-1.4.7

make
make install

Again, no problems.

cd ../asterisk-1.4.21.2/

./configure
make
make install
make samples (not required, but you will probably want the samples)

Again, compiled with no problems.

Now to install Asterisk GUI. The links that I found were all incorrect for SVN. With some research, I found out the version 2 is out, which changed the locations for the branches. The correct one is svn co http://svn.digium.com/svn/asterisk-gui/branches/2.0 asterisk-gui

cd /usr/src/

svn co http://svn.digium.com/svn/asterisk-gui/branches/2.0 asterisk-gui

./configure
make
make install
make checkconfig
— Checking Asterisk configuration to see if it will support the GUI —
* Checking for http.conf: OK
* Checking for manager.conf: OK
* Checking if HTTP is enabled: FAILED
— Please be sure you have ‘enabled = yes’
— in /etc/asterisk/http.conf
make: *** [checkconfig] Error 1

So I went into /etc/asterisk/http.conf and uncommented enabled = yes

make checkconfig
— Checking Asterisk configuration to see if it will support the GUI —
* Checking for http.conf: OK
* Checking for manager.conf: OK
* Checking if HTTP is enabled: OK
* Checking if HTTP static support is enabled: FAILED
— Please be sure you have ‘enablestatic = yes’
— in /etc/asterisk/http.conf
make: *** [checkconfig] Error 1

Again, went into /etc/asterisk/http.conf and uncommented enablestatic = yes
This happened again and again. I had to uncomment the following after all was said and done.


enabled = yes
enablestatic = yes

Then in /etc/asterisk/manager.conf
enabled = yes
webenabled = yes

It should also be noted that if you bind the address to 127.0.0.1 you will only be able to access it from that IP, so change it to 0.0.0.0 to access it from anywhere. Also, you should enable an admin account right off the bat by editing /etc/asterisk/manager.conf and putting in
[admin]
secret = yourpasswordhere
read = system,call,log,verbose,command,agent,config
write = system,call,log,verbose,command,agent,config


Now do:
modprobe zaptel
modprobe ztdummy


Add the following to your /etc/rc.local file to load these at startup.

modprobe zaptel
modprobe ztdummy
asterisk –g 

Now start asterisk and go to the configuration web gui:

asterisk -g

http://your-server-ip:8088/asterisk/static/config/cfgbasic.html

You use the admin username and password you set up previously in the manager.conf file. If you cannot login, you may want to check that file for typos.


Credit to http://www.cahilig.org/install-asterisk-14-and-asterisk-gui-ubuntu-606-lts-server-and-debian-etch
http://www.cahilig.org/install-asterisk-14-and-asterisk-gui-centos-4-and-centos-5#installation
http://asterisknow.org/install-related

Tags: asterisk

1 Comment to Asterisk on Hardy Server

1. 

   [...] http://blog.qindel.com/?p=6 - bookmarked by 1 members originally found by jaydu on 2008-10-09 Asterisk on Hardy Server http://blog.chadwollenberg.com/2008/08/26/asterisk-on-hardy-server/ - bookmarked by 6 members [...]
Bookmarks about Asterisk on October 26th, 2008

Leave a comment

You must be logged in to post a comment.